quatech water proofing car
, ,

Drylock or Sealant Flaking on Foundation Walls: Causes, Solutions, and Prevention

aquatech waterproofing worker pulling membrane window 01
When Drylock or sealant flakes off a foundation wall, the paint is rarely the real problem. This guide shows what the flaking is telling you, how to fix it properly, and when to fix the water instead.
Shawn MgGirr
SHAWN MGGIRR
Please meet Shawn, one of our basement flood experts. He started his career from the bottom, digging trenches, working his way up to contractor, supervisor. More About Shawn
Shawn MgGirr Published:

Flaking Drylock or sealant on a foundation wall is one of the most common signs of a moisture problem in a basement. When paint or sealant lifts and peels, it often means water is pushing from behind it. If you repaint without finding the cause, the new coat flakes off too, and you have spent time and money for a few months of a better-looking wall.

This guide shows what to look for, why it happens, how to fix it properly, and what it costs.

The short answer: small flakes on a wall that stays dry are usually old paint, and you can scrape and repaint. Sheets, blisters or powder, or a wall that is damp after rain, mean water, and the water has to be fixed first. See our wet basement repair service.

What to look out for

Look at the foundation walls closely, in good light:

  • Flaking or peeling. Paint or sealant lifting in small flakes, or in sheets.
  • Damp patches. Dark or discoloured areas, especially after heavy rain.
  • Moisture where flaking is worst. Flaking is often heaviest low on the wall, or near cracks and corners.
  • White powder. A chalky deposit under or around the flakes is efflorescence. See efflorescence sources and removal.

Spotting these early lets you address the moisture before it causes more damage. Our guide to the seven signs your basement needs waterproofing covers the rest.

What the flaking is telling you

The cards below match what you see to the likely cause, and show what to do.

What the flaking is telling you

Match what you see on the wall to the likely cause.

Small flakes of old paint, wall dry

Likely cause: Aging paint or a poor first coat

What to do: Scrape back to a sound surface, clean, let it dry, and repaint.

Usually fine
Sheets or blisters lifting off the wall

Likely cause: Moisture pushing from behind

What to do: Find the source of the moisture before any repainting.

Fix the water
White powder under the flakes

Likely cause: Efflorescence: water has passed through the wall

What to do: Brush the powder off, and find where the water comes in.

Fix the water
Flaking around a crack

Likely cause: Water entering at the crack

What to do: Repair the crack first, then treat the surface.

Watch it
Flaking low on the wall, worse after rain

Likely cause: Groundwater pressure or pooled water outside

What to do: Look at the grading, the gutters and the drainage.

Fix the water

A general guide. A free on-site assessment finds the real cause.

What Drylock and sealants can and can’t do

Products such as Drylock (also spelled Drylok) are masonry coatings. They can help with light dampness on a clean, dry wall. They sit on the surface, though, so they can’t hold back water that is pushing through the wall under pressure. When groundwater builds up behind the wall, it lifts the coating, and it flakes. See our guides to foundation coatings and basement waterproofing myths.

Why does this happen?

  • Moisture building up. Water or damp reaching the wall breaks the bond between the coating and the concrete.
  • Hydrostatic pressure. Saturated soil pushes water through the wall, and it lifts the coating from behind. See understanding hydrostatic pressure.
  • Poor surface preparation. A wall that was dirty, damp or covered in loose material never gave the coating a good grip. See our don’ts of waterproofing basement walls.
  • Age. Paint and sealants wear out, and flake over the years, even on a dry wall.
  • Inadequate waterproofing. Without drainage or exterior waterproofing, water keeps reaching the wall.

Fixing the cause of the moisture is the only way to stop it flaking again.

Can you just repaint it?

Use the check below to see whether a repaint will hold, or whether the water needs fixing first.

Can you just repaint it?

Two questions. Nothing is saved or sent anywhere.

A general guide. A free on-site assessment gives the real answer.

What solutions are available?

If the wall is dry: repaint properly

  1. Scrape. Remove all loose paint and sealant back to a sound surface.
  2. Clean. Brush off dust, and any efflorescence, then wash the wall.
  3. Dry. Let the wall dry fully. Tape a square of foil to it for 24 hours, and see whether moisture forms under it. See basement condensation.
  4. Repair. Fill any cracks first. See epoxy injection crack repair.
  5. Coat. Apply a masonry paint made for basement walls, following the maker’s instructions, and test a small patch first.

If the wall is damp: fix the water first

  • Interior waterproofing. An interior drain with a sump pump collects the water and sends it out, so the wall isn’t under pressure.
  • Exterior waterproofing. Exterior waterproofing stops water at the wall, with a membrane and drainage. It is the most lasting fix.
  • Drainage and grading. Clean gutters, long downspouts and sloping soil take pressure off the wall. See improving your home’s drainage.
  • Crack repair. Seal the cracks that let water in.

How much does it cost to address flaking sealants?

It depends on the cause. A repaint on a dry wall is mostly the cost of materials and your time. When the cause is water, interior waterproofing typically costs $69 to $190 per linear foot, and exterior waterproofing $110 to $500. A sump pump typically costs $550 to $3,650, and crack repair $400 to $800 per crack. Only a free on-site estimate gives you a number for your house. See our cost guide.

Why choose Aquatech Waterproofing

We have spent nearly 30 years working out why walls flake, and fixing the moisture behind them. We start with a free on-site inspection, find where the moisture comes from, and tell you honestly whether you need paint or waterproofing. Then you get a written, itemized estimate. A lifetime warranty backs every project and transfers to the next owner. Also, if you have a comparable written quote from a licensed Ontario contractor, we will match it.

FAQs about flaking sealants

What causes sealants and Drylock to flake?

The most common cause is moisture pushing from behind the coating, from damp or from groundwater pressure. Poor surface preparation, age and inadequate waterproofing also play a part. A coating can’t hold back water under pressure, so it lifts. See foundation coatings, and book a free assessment to find the cause on your wall.

How can I fix flaking sealant?

If the wall stays dry, scrape back to a sound surface, clean it, let it dry fully, fill any cracks, and repaint with a masonry paint made for basement walls. If the wall is damp, or flaking returns after rain, fix the moisture first, or the new coat will fail too. See wet basement repair.

Why does the paint keep peeling after I repaint?

Because the water is still there. Paint can’t stop water that is pushing through a wall, and the pressure lifts it again, sometimes within a season. The cure is to stop the water at its source, with drainage or exterior waterproofing, then finish the wall. See basement waterproofing myths.
Interior drainage with a sump pump, exterior waterproofing, better drainage and grading, and repairing cracks and leaks. Which one fits depends on where the water comes from. See water control vs waterproofing, interior waterproofing and exterior waterproofing.

Is the white powder under the flakes mold?

Usually not. A white, chalky powder is typically efflorescence, a mineral deposit left as water moves through concrete. It isn’t mold, but it means water is getting through, and mold can follow. Brush it off and watch whether it returns. See efflorescence sources and removal and harmful mold and mildew.

How much does it cost to waterproof a basement?

It depends on the cause. Interior waterproofing typically costs $69 to $190 per linear foot, exterior waterproofing $110 to $500, a sump pump $550 to $3,650 and crack repair $400 to $800 per crack. A free on-site estimate gives you a number for your house. See our cost guide.

How can I prevent sealant flaking?

Keep water away from the foundation, with clean gutters, long downspouts and soil that slopes away. Repair leaks and cracks promptly, prepare the wall properly before any coating, and check the walls every year. See how often to check your waterproofing and how gutters affect waterproofing.

Is flaking paint on a basement wall dangerous?

The paint itself isn’t the concern. The damp behind it is, because damp feeds mold and weakens materials over time. If the wall is damp, find the source. If the house is old, ask a professional before scraping old paint, since it may contain lead. See how to determine the source of moisture.

Is your wall flaking again?

Book a free assessment. We will find where the moisture comes from, tell you what the wall needs, and give you a written, itemized estimate. You can also call 647-794-1701 or 866-620-8492.